If FLOCCULANT TABS agent is used, these fine particles will be transformed into a form that may be removed through filtration in sand or cartridge filters. One of the most frequent problems occurring during care of water in the pool is creation of turbidity caused due to fine mechanical or organic impurities or remnants after algae liquidation. If you do not succeed in altering the water in the pool to the quality required, the whole procedure is to be repeated. Big floccules may also be removed from the pool bottom by means of a pool vacuum cleaner while the circulation is switched off. Then the circulation will remain switched on again till the next day, as a result of which the floccules created become caught in the filter.
The added amount is evenly spread on the water level in the deepest part of the pool, preferably in the evening, water is mixed for a short time and then the water circulation is turned off for about one hour.
#CHLORINATING TABS PLUS PLUS#
If FLOCCULANT GRANULAR agent is used, these fine particles will be transformed into a form that may be removed through filtration in sand or cartridge filters.īefore the agent is added into the pool, the water pH value must be altered first using pH MINUS or pH PLUS agents according to the instructions for use shown on the relevant agent packing so that it is in the range between 7.2 and 7.6.ĭepending on the level of water contamination, FLOCCULANT GRANULAR agent in the amount of 20 - 40 g is added to each 10 m 3 of water in the pool. During this period, big floccules of impurities will precipitate in water they may be removed by means of a pool vacuum cleaner or may be caught during filtration. Then the circulation will be switched off for 12 hours. The measured amount is diluted in water (50-100 ml of the agent per 1 litre of water) and is evenly sprinkled on the water level with the water circulation turned on for about four hours in order to mix the agent with water. If FLOCCULANT LIQUID agent is used, these fine particles will be transformed into a form that may be removed through filtration in sand or cartridge filters.īefore the agent is added into the pool, the water pH value must be altered first using pH MINUS or pH PLUS agents according to the instructions for use shown on the relevant agent packing so that it is in the range between 6.5 and 6.8.ĭepending on the level of water contamination, FLOCCULANT LIQUID agent in the amount of 10 - 50 ml is added to each 10 m 3 of water in the pool.
The greasy line around the water level is removed so that the solution or the agent is applied when the water level is decreased by 5-10 cm, and is then wiped off with a wet cloth or sponge (the cloth or the sponge is never rinsed in the water contained in the pool).
When the water is discharged from the pool, the prepared solution or the concentrated agent is applied onto wet surfaces and the surfaces are cleaned with a wet brush and rinsed with water the rinsing water is then discharged from the pool. Depending on the level of contamination the agent may be used either diluted in water in the ratio from 1:3 to 1:30 (1 litre of the agent diluted in 3 to 30 litres of water), or concentrated – which is enabled due to its gel consistency. The alkaline gel cleaning agent is designed to clean all kinds of pool foils and pool wall and bottom materials before the pool is used as well as during its operation. Killed algae should be filtered off with a filtrating unit, remaining algae are to be removed through flocculation – use FLOCCULANT LIQUID or FLOCCULANT GRANULAR agents according to the instructions for use shown on the relevant agent packing. If undesired algae still occur, use a single amount of the agent equal to 300-400 ml per 10 m 3. The agent is to be added into the pool with the circulation device switched on as follows: ALGAE STOP is suitable to be used as prevention together with disinfecting agents based on active chlorine or oxygen. Algae are often a cause of turbidity and slimy sediments created on the pool bottom and walls.
Occurrence of various kinds of algae is one of the most frequent problems to be dealt with during pool water treatment.
0 kommentar(er)
